---
title: Luxafor Cube 2 Manual
description: "The Luxafor Cube 2 is a wireless busy light with a built-in battery. You change your status by turning it onto a different side. This manual covers setup, charging, modes and specifications. [![Luxafor Cube 2](https://luxafor.com/wp-content/uploads/2026/11/Luxafor-Cube-2--300x300.webp)](https://luxafor.com/wp-content/uploads/2026/11/Luxafor-Cube-2-.webp) ## What’s in the box…"
url: "https://luxafor.com/help/manuals/cube-2-manual/"
updated: "2026-11-17"
category: Manuals
---

# Luxafor Cube 2 Manual

The Luxafor Cube 2 is a wireless busy light with a built-in battery. You change your status by turning it onto a different side. This manual covers setup, charging, modes and specifications. [![Luxafor Cube 2](https://luxafor.com/wp-content/uploads/2026/11/Luxafor-Cube-2--300x300.webp)](https://luxafor.com/wp-content/uploads/2026/11/Luxafor-Cube-2-.webp)

## What’s in the box

- 1 Luxafor Cube 2, with a magnet built into its back
- 1 USB-A to USB-C charging cable, 25 cm (10 in)
- 1 magnet with double-sided tape, for you to stick on a surface you choose
- 4 anti-slip pads

 The anti-slip pads are not stuck on the Cube 2, so you can choose how to place it. Use the magnet on a wall or on a surface where you do not use the pads, and use the pads on a desk. See [Set up](https://luxafor.com/help/manuals/cube-2-manual/#set-up).

## Get to know your Cube 2

 ![Back of the Luxafor Cube 2 with numbered button, USB-C port, charging indicator and anti-slip pad positions](https://luxafor.com/wp-content/uploads/2026/11/cube-2-manual-back-01.webp)

| Number | Part | What it does |
| --- | --- | --- |
| 1 | Button | Turns the Cube 2 on and off, and switches modes |
| 2 | USB-C port | Charges the Cube 2 |
| 3 | Charging indicator | Shows the charging state, above the USB-C port |
| 4 | Anti-slip pads | Keep the Cube 2 in place on a desk. Stick one on each corner. |

## Charge the Cube 2

1. Charge the Cube 2 fully before the first use.
2. Plug the USB charging cable into a USB charger.
3. Plug the other end into the USB-C port on the back of the Cube 2. The charging indicator blinks red.
4. Wait until the charging indicator turns green. The Cube 2 is full.

 You can use the Cube 2 while it charges. If it is off, it turns on when charging starts. **Note:** If the battery is empty, the Cube 2 may stay off at first. It charges for a short time, then turns on by itself.

## Set up

 Choose how you want to place the Cube 2.

#### Place it on a desk

1. Take the 4 anti-slip pads from the box.
2. Stick one pad on each corner of the back of the Cube 2.
3. Put the Cube 2 on a desk or any other flat surface.

#### Place it with the magnet

 The Cube 2 has a magnet built into its back. Use the magnet from the box to place the Cube 2 on a wall, desk or workstation. Leave the anti-slip pads off.

1. Remove the plastic from the double-sided tape on the magnet.
2. Stick the magnet on the surface where you want the Cube 2.
3. Attach the Cube 2 to the magnet.

 Use a dry, clean and smooth surface. The magnet holds better there. You can stick the magnet only once. For the surfaces to avoid and the mounting times, see [Mount the magnet](https://luxafor.com/help/manuals/switch-pro-2-manual/#mount-the-magnet) in the Switch Pro 2 manual.

#### Turn it on

1. Press the button on the back once, briefly.

## Use the Cube 2

#### Change the color

 Turn the Cube 2 onto a different side to change the color. The picture shows four colors: green, red, yellow and blue. ![Four Luxafor Cube 2 units glowing green, red, yellow and blue](https://luxafor.com/wp-content/uploads/2026/11/cube-2-manual-colors-01.webp) Hold the Cube 2 in its natural position, with the charging port and the button at the bottom. It shows red. Turn it clockwise, and the next colors are blue, then yellow, then green.

#### Turn it off

1. Press the button on the back once, briefly.
2. Release the button when the LEDs go out.

#### Sleep mode

 Lay the Cube 2 face up. It does not turn off. It goes into Sleep mode and lights up again when you stand it upright. Blue lights flash for a short time when you lay it down.

#### Eco mode

 Eco mode makes the battery last longer. The Cube 2 uses 1 LED instead of 6, which saves energy. See [Technical specifications](https://luxafor.com/help/manuals/cube-2-manual/#technical-specifications) for the battery life.

1. Hold the button on the back for 2 to 3 seconds.
2. Release the button when the Cube 2 turns yellow. Eco mode is on.

 To turn Eco mode off, hold the button again for 2 seconds.

#### Check the battery level

1. Lay the Cube 2 face up. The LEDs light up cyan.
2. Count the lit LEDs. More LEDs means more charge.

 ![Six LEDs of the Cube 2 numbered 1 to 6 clockwise from the top right](https://luxafor.com/wp-content/uploads/2026/11/cube-2-manual-battery-01.webp)

- All 6 LEDs lit: the battery is full.
- The LEDs go out one by one as the battery drains, starting with LED 1 and going clockwise.
- Only LED 6 lit (upper left): the battery is almost empty. Charge the Cube 2 now.

## Button guide

 The button on the back does different things depending on how long you hold it. ![Timeline of button presses: short click turns on or off, 2 to 3 seconds Eco mode, 3 to 5 seconds Cube or Switch mode, more than 10 seconds Switch pairing mode](https://luxafor.com/wp-content/uploads/2026/11/cube-2-manual-button-timeline-01.webp)

| How long you hold | What happens |
| --- | --- |
| Short click | Turns the Cube 2 on or off |
| 2 to 3 seconds | Turns Eco mode on or off (yellow) |
| 3 to 5 seconds | Switches between Cube mode and Switch mode (cyan) |
| More than 10 seconds | Starts Switch pairing (purple) |

## Switch mode

 The Cube 2 works on its own in Cube mode, with solid colors. In Switch mode, it connects to a Luxafor Bluetooth Pro, or to an older-generation Luxafor Bluetooth device, and works as its remote control. A Cube 2 with a Bluetooth Pro is the Luxafor Switch Pro 2. See the [Luxafor Switch Pro 2 manual](https://luxafor.com/help/manuals/switch-pro-2-manual/). The range depends on the device you pair with. The Cube 2 reaches up to 80 m (262 ft), and the Bluetooth Pro reaches up to 25 m (82 ft).

#### Turn on Switch mode

1. Turn on the Luxafor Bluetooth device.
2. Hold the button on the Cube 2 for about 3 seconds, until the Cube 2 turns cyan.
3. Release the button. The Cube 2 pulses red and runs red clockwise. It is looking for the Bluetooth device.

 To go back to Cube mode, hold the button for 3 to 5 seconds until the Cube 2 turns cyan again.

#### Pair with a new device

 Use these steps if the Cube 2 and the Bluetooth device do not connect.

1. Hold the button on the Cube 2 for about 10 seconds, until the Cube 2 turns purple.
2. Release the button. The purple light runs clockwise. The Cube 2 is looking for a new Luxafor Bluetooth device.

## What the colors mean

| Indicator | Meaning |
| --- | --- |
| Blue, flashing | You laid the Cube 2 face up (Sleep mode) |
| Yellow | You held the button to turn Eco mode on or off |
| Cyan | You held the button to switch between Cube mode and Switch mode. Also shows the battery level when the Cube 2 is face up. |
| Red, running clockwise | Switch mode: looking for the Bluetooth device it was connected to |
| Purple, running clockwise | Switch mode: looking for a new Bluetooth device |
| Charging indicator, blinking red | Charging |
| Charging indicator, green | Fully charged |

## Technical specifications

| Specification | Value |
| --- | --- |
| Dimensions | 56 × 56 × 26 mm (2.20 × 2.20 × 1.02 in) |
| Weight | 68 g |
| Light | 6 RGB LEDs |
| Connection | Bluetooth |
| Range | Up to 80 m (262 ft) without obstacles |
| Battery | Built-in, 1200 mAh |
| Charging | USB-C port, with the USB-A to USB-C cable (included) |
| Power consumption | Up to 26 mA |

#### Battery life

 Battery life with non-stop use depends on the color and on Eco mode.

| Color | Normal | Eco mode |
| --- | --- | --- |
| Yellow | 46 hours | 58 hours |
| Green, red or blue | 73 hours | 90 hours |

## Still need help?

 [Send us a message](https://luxafor.com/help/contact/) and tell us:

- which device you have and where you bought it
- what you see, and what you expected to see
- which steps on this page you have already tried
- your order number, if you have one

 A short video or photo of the problem helps us fix it faster. If the problem is with the connection, film the device at the moment it tries to connect.
